| Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software | |
|
Author | Message |
---|
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:36 am | |
| Problem Description: Initializing... DA_LIB_VER_3.2.0.7 It is sensing the pinout fast,please hold on the phone Power key RXD=6 TXD=7 Connecting...Please hold on the POWER key until the red gauge is going... Failed to read HardCode, REG=0x80000008 Error: Failed to read REG=0x80010008 Error: Failed to read REG=0x84010008 Error: Failed to read REG=0x80001008 Reason: Bad Flash IC or Bad Cable Solution: 1. Can try to change cable, try with slower baudrate and try few times. 2. Rehot the flash IC and try again. if still not then need replace flash IC/ @ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:37 am | |
| Problem Description: Flashing stops at different percentage everytime. Means first try it stop at 30%, next time it stop at 35%, then 10% and so and so. Reason: This can be due to: 1. Bad Flash Chip 2. Low power to handset 3. Bad data inside Flash Chip Solution: First i suggest to try with slow baudrate, try flash with slow baudrate. if this not success then better erase the complete flash chip and then try again. This should sure help if its not a hardware fault. If it still not helps, means can be hardware problem too, in this case you can reflow the Flash IC or replace if necessary.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:37 am | |
| Problem Description: Not able to work correctly on MTK CPU ID 6217. Reason: Unsupported Boot type Solution: You need to use supported boot type for this CPU ID. Just select "Boot 3.848" and it should work ok.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:38 am | |
| Problem Description: "SPD USB TO SERIAL NOT FOUND" Reason: The drivers are not installed for SpreadTrum USB communication Solution: You need to install the USB drivers for SpreadTrum. when UCT box has finished finding the pinouts for spreadturm handset, it will ask for SPD drivers, these drivers can be found inside folder: "C:\UCT\UCT\SpreadTrum_USB_Drivers\" just need to install them and then UCT can start working your handset. If in case the computer not asks for any drivers after pinfinding, then you need to un-install the bad drivers from your device manager and then again re-install the supplied drivers.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:38 am | |
| Problem Description: "Failed to format Flash" Reason: Cannot format the flash for older type handsets, cause they not support new boot type. Solution: Just try different boot types and it should be ok. Some boot can work for some handsets. This is why it is not important that the latest boot will always work for all handsets. it can be also that only old boot type will work for some particular handsets.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:38 am | |
| Problem Description: Error "Project ID not found" while connecting the handset Reason: UCT Software is not able to find the project id inside the handset flash, project id is the version of the firmware. This can be cause of wrong boot selection, wrong memory type selection or can be due to empty flash chip or hardware fault. Solution: to solve this, first try with different boot type and mode type, try all boot and also try with "NAND" memeory type as well. if still not works, then flash the handset with good flash file. if not able to flash, means bad flash chip, try reflow or replace.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:39 am | |
| Problem Description: Spreadturm handsets show "Failed to RXD" Reason: This error can be cause of many problems. can be cause of wrong connectivily, bad cable, wrong boot type Solution: Select "6600L-USB" or "6600L-USB" in options and try again
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:39 am | |
| Problem Description: Error: Unsaft EFS Address, Please input the right format address and try again. Failed to auto format. Reason: UCT Software is not able to recognise the flash addresses inside handset Solution: Try to do "Reset", If this not helps then only way to fix this is by flashing handset with correct flash file, if u dont have a flash file then u need to arrange a similar handset, read the flash from it and then flash it to your faulty handset.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:39 am | |
| Problem Description: Read Info, Read Flash working fine for SPD handset, but format anf write flash not working properly. Reason: you are not sellecting the correct option type according to cpu id and flash id. Solution: Make readInfo of the handset, here in information you will see the CPU type and the flash type of the handset, for eg. CPU: 6600xxxxxxxxx Flash: NOR. Now in this case, you need to select the option "6600L-USB" and then proceed. Means it is very important to select the correct options, otherwise format, write flash will not work properly. for details, better read complete guide for SpreadTrum phones.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:40 am | |
| Problem Description: Nor Flash ID: 0000000000000000 Nand Flash ID: 0000000000000000 Nor Flash not found. Reason: Bad flash IC Solution: You need to replace the flash IC
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:40 am | |
| Problem Description: Initializing... DA_LIB_VER_2.5.1.2 It is sensing the pinout fast,please hold on the phone Power key RXD=4 TXD=7 Connecting...Please hold on the POWER key until the red gauge is going... BB:6227, HardwareVer:8A05, SoftwareVer:8A00 Set RTC Alarm Mask failed, REG=0x405600780 Reason: Problem is due to low power to handset Solution: Keep and press the power button during complete operation. this might help.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:41 am | |
| Problem Description: Nor Flash ID: 0098000300000000 Nand Flash ID: 0000000000000000 Read Hardware Information is done. Get Project ID from phone... Project ID: M.RK3230436.M28202.V1.1.0.0M1226 Changing baudrate to 921600... Done. Reading full Flash... CRC error: CRC=4C92, CheckSum16=4C8A Reason: Bad CRC checksum inside the flash of handset. this is due to bugs inside handset firmware Solution: You need to format the handset first before any other operation.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:41 am | |
| Problem Description: Read info is done. CPU: SC6600R Flash: NAND_H8BCS0PG0MBP Set FLASH Parameters... Settings have been completed! Reading FileSystem info... Failed to read FS info. Reason: The File System is not found by software Solution: Only way to solve this is by flashing the handset with correct flash file, or need to read flash from a working handset and then flash it to faulty handset.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:41 am | |
| Problem Description: setting the Flash Parameters... Settings have been completed! Reading FileSystem info... Error: Get Flash die baseaddress Reason: Phone has been tampered with other software or the firmware inside has been corrupted. Solution: You need to look for the Full flash file of this handset and flash to it, If u dont find a flash file in that case you need to look for a working handset and read flash from it, then flash it to your dead handset.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:42 am | |
| Problem Description: Get error "Invalid IMEI" when trying to repair IMEI for some MTK handsets Reason: Some handsets, mostly of CPU 6235 and 6253 have this problem after format. After format cannot write IMEI and show error Invalid IMEI Solution: To solve this you need to flash the handset. There is no other way to solve this problem for now. But you can avoid this error by taking NV data backup before formatting the handset. Just select NV Editor and take full backup of handset before formatting. After format, write NV data back to handset and then fix IMEI.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:42 am | |
| Problem Description: How to solve error: FAILED TO RUN BOOTLOADER Reason: Communication is stopped in middle with handset and UCT Box Solution: Press and hold the power button untill all process is completed, if even this not help then press and hold * key and keep pressed untill all completed
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:42 am | |
| Problem Description: How to solve the error: ERROR: MTK_DA_GET_FAT_INFO_NOT_FOUND Reason: UCT Software is not able to read the FAT information from the MTK handset, this is because of un-compatible flash chip or boot type. Solution: Try to select Boot "Ver. 3.952" from the options, if even this not works, then try other options one-by-one.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:43 am | |
| Problem Description: Error: RXD<>MaxBuffSize, Please close all other program or change baudrate and try again. Reason: Software not able to buffer the data Solution: Select baud 921600 and try again
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:43 am | |
| Problem Description: Changing baudrate... Failed to set baudrate... Reason: Usually driver problem. Communication between phone and pc is poor. Solution: 1. Try with option "6600L-USB" or "6600L-COM" and try again. 2. Try to un-install spreadtrum drivers and install again. 3. Try with smaller baudrate. 4. Try with any other computer. Should work 5. if still not solve and handset is dead, can be 99% hardware problem.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:44 am | |
| Problem Description: Changing baudrate... Failed to set baudrate... Reason: Usually driver problem. Communication between phone and pc is poor. Solution: 1. Try with option "6600L-USB" or "6600L-COM" and try again. 2. Try to un-install spreadtrum drivers and install again. 3. Try with smaller baudrate. 4. Try with any other computer. Should work 5. if still not solve and handset is dead, can be 99% hardware problem.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:44 am | |
| Problem Description: Cannot connect SPD handsets with in-built battery Solution: Just press the * and # button on the handset and then press "Start" in UCT Software. All Should be ok now.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:45 am | |
| Problem Description: Initializing... DA_LIB_VER_2.5.1.2 It is sensing the pinout fast... D-=9 D+=14 BOOT set failure, continue to scan... Sense failure Reason: Pinout Finding is correct, but UCT is not able to boot the handset. Solution: 1. If your handset have a inbuilt battery then press * and # on the phone and keep them pressed and then try to connect the handset 2. Press and hold 0 and power button on the handset and then try to connect the handset. 3. If above not work, then press and hold * button on the handset and then try to connect the handset. 4. If above not work, then press and hold 0 button on the handset and then try to connect the handset. 5. If you still cannot solve this problem, then try to locate Rx and Tx on the handset and connect using them and select "6600L-COM"
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:45 am | |
| Problem Description: Cannot enter tracker or cannot boot in meta mode Initializing... DA_LIB_VER_3.2.2.8 It is sensing the pinout fast,please hold on the phone Power key RXD=8 TXD=4 Connecting...Please hold on the POWER key until the red gauge is going... BB:6226, HardwareVer:8A02, SoftwareVer:8A01 Read info...ok, Waitting enter meta... Connection time out. Reason: Low power to handset Solution: 1. Take a power supply or the handset battery and connect it to the + and - of the handset. 2. Connect the ground only (-) from the UCT Box Main cable to the handset, dont connect the positive nide (+). 3. Try now to connect and all should be ok.
@ |
|
| |
warrior Trail Moderator
Posts : 2495 Thanks : 12966 THANKS : 74 Join date : 2013-09-09
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software Fri Aug 15, 2014 1:45 am | |
| Problem Description: Not able to connect handset with CPU 6217 Reason: Not supported by old boot versions Solution: Select Boots: Ver3.848 in the Options and then try again
@ |
|
| |
Sponsored content
| Subject: Re: Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software | |
| |
|
| |
| Some Tips, Tricks, Guides, Solutions, Troubleshoot for UCT Box Software | |
|