Admin
Admin
Posts : 3981
Thanks : 18807
THANKS : 36
Join date : 2012-09-02
Age : 35
Location : INDIA, TAMILNADU
 |  Subject: how-to-flash-samsung-monte-s5620-guide  Sat Jan 26, 2013 12:50 am | |
| Flashing the newer phones is much like any Samsung handset using the Touch Wizard over Samsung OS. We are sharing with you How to Flash Samsung Monte s5620. It really works 100%. I have already flashed my Samsung Monte S5620, hence we are going to share with you.Follow the below steps :Prepare Your Computer1. Install Kies on your computer and make sure it will communicate with your phone, or install only the driver pack.
2. Disconnect your phone and Close NPS.
3. Click “Start” or the Windows
logo on the bottom left of your computer screen and click in the
search/run box and type msconfig.
4. Select the tab marked “Start Up” and click “disable all” and click ok.
5. Restart the computer and you are ready to flash.
DO NOT! run NPS
or Kies again until you have successfully flashed your phone! After you
have successfully flashed your phone, you must reset the Windows setting
back to there original and restart your computer.
Check List1. USB cable that came with your phone.2. Kies or Drivers installed3. Multiloader software for flashing your Samsung Monte.4. New firmware (Download from any trusted website)Warning!Make
sure your phone dose not have sim lock or net lock before you try and
flash. Type *#7465625# and make sure the SIMLOCK and NETWORKLOCK is OFF,
if it is ON you MUST Unlock it or you will freeze your phone! Or you
just type on the screen *2767*3855# and your phone will be factory reset.Prepare Your Phone for Flashing1. Make sure Samsung PC Studio/Samsung Kies is installed and communicates with your phone. And unpack the firmware in a folder you can easily find it.
2. Remove the Sim and MicroSD from your phone and replace the battery.
3. Make sure that your phone is off and not connected to the computer.
4. Hold down the “Volume
-” button on the left or right side differs, and the “Camera” button on
the right, then press the “Power” button (all three buttons need to be
pressed together). Your phone should start up into a red\blue on black download screen.)5. Now run MultiLoader6. Plug the phone up to the computer.Multiloader Steps/ Formatting Steps1. Select the radio button BRCM2153 (for S5620 etc…) Wave S8500 use LSI64102. Select Boot Change3. Full Download4. Master romNow Select these files in this order, you will have to switch between the contained directories as you load file.5. Boot6. Amss7. Apps8. Rsrc19. Rsrc2(Low) (Warning! Do not use Rsrc2 (Mid) your phone may not restart!!!)10. Factory FS file.11. CSC (remember this is in a separate folder)12. SHP13. SPP14. PFS***FOTA and ETC fields are left blank.****15. Click the Port Search button, it will find your phone and show the com port is ready.16. Click the download button and be patient, this will only take a few minutes to complete.17. When it’s finished, it will show “ok complete”.NOTE - If yours does not restart at this point, take out the battery a few seconds then reinsert it.18. Unplug the phone from the USB cable, reinstall the sim and SD card.19. Now with every thing is complete, You can perform a hard reset by typing *2767*3855# into the hand set.20. When the phone resets type *#1234# into your handset to check your new firmware ver.NOTE - If your phone fails the flash for any reason, DO NOT TRY AND RESTART IT!!!!! Restart the computer and try the flash again! |
|
Iphone Australia Networks 
Iphone U.S.A Networks 
Iphone U.K Networks 
Iphone France Networks 
Iphone Canada Networks 
Iphone Swizerland Networks Unlock Now FRIENDUNLOCKER
